沸腾干燥机典型的系统
双层沸腾干燥机/冷却器

Kason（凯胜）的双层，圆形流化床处理器显着降低资本成本，能耗和占地空间每磅产品的干燥或冷却。
的上部甲板的加入使得使用，否则将被耗尽后的下层通过加热或冷却的空气，并且需要在尺寸或不平衡重量电机或风机的能源消耗几乎没有增加，几乎加倍容量和几乎没有增加经营成本或建筑面积的效率。

与矩形流化床处理器，需要重轨的建设，经受住不断振动，循环流化床处理器本质上是刚性的，从而使材料的建设是衡量和振动电机精简。也消除了相关部件，如多个风口和出风口及其相关的管道 - 圆形装置，只需要一个每个。其结果是一个单元的显着较轻的重量和较高的工作效率，与较低的资本成本和更小的体积，相当于床范围和容量比矩形流化床处理器。
减少材料，焊缝，以及相关的劳动降低制造成本，特别是在单位完成FDA，USDA，BISSC或3-A标准。

减少焊缝，一个快速断开住房，而没有内部横梁，循环流化床处理器减少清洗时间显着。

正在申请专利的双层流化床系列处理器，直径从48“至84”（1220毫米2135毫米），四种型号的满足中，大批量的生产要求。可配置为连续的干燥，冷却或保湿的应用程序。

标准装备：
控制入口温度，空气流速，床的深度和停留时间，
快速断开夹具，快速，彻底的清洁
，流化床空气分配器的选择
高扭矩马达驱动双延伸轴和偏心重量调整系统，以优化特定材料的振动运动
连续或间歇操作
304不锈钢接触面
可调式溢流堰控制层的深度
选装配置：
3A，FDA，和BISSC标准建设
就地清洁喷头
防爆电气恶劣环境应用
316或更高等级的不锈钢材料接触面

Vibro-BedTM TYPICAL SYSTEMS
Double-Deck Fluid Bed Dryer/Cooler
Kason's Double-Deck, Circular Vibratory Fluid Bed Processor significantly reduces capital cost, energy usage and floor space per pound of product being dried or cooled.
The addition of an upper deck makes use of heated or cooled air that would otherwise be exhausted after passing through the lower deck, and requires little to no increase in the size or energy consumption of imbalanced-weight motors or blower fans, nearly doubling capacity and efficiency with little to no increase in operating cost or floor space.

Unlike rectangular fluid bed processors that require heavy-gauge construction to withstand constant vibration, circular fluid bed processors are inherently rigid, allowing materials of construction to be down-gauged and vibratory motors to bedownsized. Associated components are also eliminated, such as multiple air inlets and outlets and their associated ducting — the circular unit requiring only one of each. The result is a unit of significantly lighter weight and higher operating efficiency, with lower capital cost and a smaller footprint, than rectangular fluid bed processors of equivalent bed area and capacity.
Reductions in material, weld seams, and associated labor decrease fabrication cost, particularly when units are finished to FDA, USDA, BISSC or 3-A standards.

With reduced weld seams, a quick-disconnect housing, and no internal cross-members, circular fluid bed processors cut cleaning time dramatically.

Four models of the patent pending, double-deck fluid bed processor range in diameter from 48" to 84" (1220mm to 2135mm), satisfying medium- to high-volume production requirements. All are available configured for continuous drying, cooling or moisturizing applications.

Standard Equipment:
Controls for inlet temperature, air velocity, bed depth, and retention time
Quick-disconnect clamps for fast, thorough cleaning
Choice of fluid bed air distributor
High Torque motor drive with double extension shaft and eccentric weight adjustment system to optimize vibratory motion for specific materials
Continuous or batch operation
304 Stainless steel contact surfaces
Adjustable weir to control bed depth
Optional Equipment:
Construction to 3A, FDA, and BISSC standards
Clean-in-place spray heads
Explosion proof electricals for hazardous applications
316 or higher grade stainless steel material contact surfaces